Pin |
Description |
Pin |
Description |
1 |
- |
45 |
Inhibitor switch signal 'S2' |
2 |
- |
46 |
Inhibitor switch signal 'S3' |
3 |
- |
47 |
Inhibitor switch signal 'S4' |
4 |
- |
48 |
- |
5 |
- |
49 |
- |
6 |
- |
50 |
- |
7 |
- |
51 |
- |
8 |
- |
52 |
- |
9 |
- |
53 |
- |
10 |
CAN communication line (HIGH) |
54 |
Sports mode down switch |
11 |
- |
55 |
- |
12 |
- |
56 |
- |
13 |
- |
57 |
- |
14 |
- |
58 |
- |
15 |
- |
59 |
- |
16 |
- |
60 |
- |
17 |
- |
61 |
- |
18 |
- |
62 |
- |
19 |
- |
63 |
- |
20 |
- |
64 |
- |
21 |
- |
65 |
- |
22 |
- |
66 |
- |
23 |
- |
67 |
- |
24 |
- |
68 |
- |
25 |
- |
69 |
- |
26 |
- |
70 |
- |
27 |
Ignition switch |
71 |
- |
28 |
- |
72 |
- |
29 |
Sports mode up switch |
73 |
- |
30 |
- |
74 |
- |
31 |
- |
75 |
- |
32 |
- |
76 |
- |
33 |
- |
77 |
- |
34 |
- |
78 |
|
35 |
CAN communication line Low |
79 |
Sports mode Select switch |
36 |
- |
80 |
- |
37 |
- |
81 |
- |
38 |
- |
82 |
- |
39 |
- |
83 |
- |
40 |
- |
84 |
Shift lock solenoid |
41 |
- |
85 |
Reverse lamp relay |
42 |
- |
86 |
P/N relay |
43 |
- |
87 |
- |
44 |
Inhibitor switch signal 'S1' |
88 |
- |
Pin |
Description |
Pin |
Description |
1 |
Overdrive clutch control solenoid valve (VFS) |
52 |
Underdrive brake control solenoid valve (VFS) |
3 |
Input speed sensor signal |
53 |
SS-B Solenoid valve (ON/OFF) |
4 |
Output speed sensor signal |
54 |
Output speed sensor power |
26 |
Torque converter control solenoid valve (VFS) |
55 |
Oil temperature sensor (-) |
27 |
35R Clutch control solenoid valve (VFS) |
57 |
Oil temperature sensor (+) |
28 |
SS-A Solenoid valve (ON/OFF) |
76 |
Solenoid valve power 1 |
29 |
Input speed sensor power |
77 |
Solenoid valve power 2 |
51 |
Line pressure control solenoid valve (VFS) |
78 |
26 Brake control solenoid valve (VFS) |
Speakers Replacement
Front Speaker
1.
Remove the front door trim.
(Refer to Body - "Front door")
2.
Remove the front speaker (A) after removing ...
Direct Electro Hydraulic Actuator Coupling Components
1. Coupling assembly
2. Input shaft
3. Pressure sensor
4. Extension wiring
5. Oil hydraulic Motor(Actuator)
...
ECM Problem Inspection Procedure
1.
TEST ECM GROUND CIRCUIT: Measure resistance between ECM and chassis
ground using the backside of ECM harness connector as ECM side check
point. If the problem is fo ...