Kia Optima Manuals

Kia Sorento: Removal - SS-A Solenoid Valve(ON/OFF) - Automatic Transaxle Control System - Automatic Transaxle System - Kia Sorento XM 2011-2019 Service ManualKia Sorento: Removal

Second Generation XM (2011-2019) / Kia Sorento XM 2011-2019 Service Manual / Automatic Transaxle System / Automatic Transaxle Control System / SS-A Solenoid Valve(ON/OFF) / Removal

1.
Remove the air duct.
(Refer to Engine Mechanical System - "Air cleaner")
2.
Remove the battery and the battery tray.
(Refer to Engine Electrical System - "Battery")
3.
Remove the under cover.
(Refer to Engine Mechanical System - "Engine Room Under Cover")
4.
Drain the coolant.
(Refer to Engine Mechanical System - "Coolant")
5.
Remove the drain plug (A) and reinstall the drain plug after draining ATF totally.
Tightening torque :
38.2 ~ 48.1 N.m (3.9 ~ 4.9 kgf.m, 28.2 ~ 35.4 lb-ft)

  
Replace the gasket before reinstalling the drain plug.
6.
Remove the wiring bracket installation bolt (A).
7.
Remove the ATF Injection hole(eyebolt) (A).

  
Replace the O-Ring (A) before reinstalling the eyebolt.
8.
Disconnect the coolant hose (B) after removing the coolant hose clamp (A).
9.
Disconnect the hose (B) after removing the automatic transaxle fluid cooler hose clamp (A).

  
When hose & pipe assembly
Align marking of pipe (B), marking of hose (A), and matching color each other.
10.
Remove the valve body cover (A).
Tightening torque:
(A) 13.7 ~ 15.7 N.m (1.4 ~ 1.6 kgf.m, 10.1 ~ 11.6 lb-ft)

  
•
Replace the gasket (A) before reinstalling the valve body cover.

11.
Remove the bolts (C) after disconnecting the solenoid valve connector (B) and the oil temperature sensor connector (A).
Tightening torque :
9.8 ~ 11.8 N.m (1.0 ~ 1.2 kgf.m, 7.2 ~ 8.7 lb-ft)

12.
Remove the solenoid valve support bracket (A).
Tightening torque :
9.8 ~ 11.8 N.m (1.0 ~ 1.2 kgf.m, 7.2 ~ 8.7 lb-ft)

13.
Remove the solenoid valve (A).

  
•
When installing, apply the ATF oil or white vaseline to the O-ring (A) not to be damaged.

Inspection
1. Turn ignition switch OFF. 2. Remove the air duct. (Refer to Engine Mechanical System - "Air cleaner") ...

Installation
1. Install in the reverse order of removal.    • ...

See also:

SRS components and functions
The SRS consists of the following components: 1. Driver's front air bag module 2. Passenger's front air bag module 3. Side impact air bag modules 4. Curtain air bag modules 5. Retractor ...

Removal
1. Turn the ignition switch OFF and disconnect the battery negative (-) cable. 2. Disconnect the engine coolant temperature sensor connecto ...

Passenger Airbag (PAB) Module Description
Passenger Airbag (PAB) module is located in the passenger crash pad. This PAB contains 2 firing squibs of airbag and 1 firing squib of active vent. Depending of crash speed or the tightening ...

Categories

Copyright © www.ksmanual.com 2014-2019