Kia Optima Manuals

Kia Sorento: Instrument Cluster Inspection - Indicators And Gauges - Body Electrical System - Kia Sorento XM 2011-2026 Service ManualKia Sorento: Instrument Cluster Inspection

Second Generation XM (2011-2026) / Kia Sorento XM 2011-2026 Service Manual / Body Electrical System / Indicators And Gauges / Instrument Cluster Inspection

1.
Check the suspected area as below table when the warning light is error.
NO
 Warning light
 Description
 Communication
 Signal (Unit/Sensor)
 Suspected Area
1

Turn signal -LH
 C-CAN
 IPM
1.
CAN line faulty
2

Turn signal -RH
 C-CAN
3

Cruise
 C-CAN
 SCC
EMS
1.
CAN line faulty
4

SET
 C-CAN
 EMS
1.
CAN line faulty
5

Front fog
 C-CAN
 IPM
1.
CAN line faulty
6

Tail lamp ON
 C-CAN
 BCM
1.
CAN line faulty
7

Head lamp low beam
 C-CAN
 IPM
1.
CAN line faulty
8

ECO
 Hardwire
 　
 　
9

Head lamp high beam
 C-CAN
 BCM
1.
CAN line faulty
10

Seat belt
 C-CAN
 BCM
1.
CAN line faulty
11

Air bag
 C-CAN
 ACU
1.
CAN line faulty
12

Oil pressure
 Hardwire
 Oil pressure sensor
1.
Wiring faulty
13

Oil level
 C-CAN
 EMS
1.
CAN line faulty
14

Battery charge
 Hardwire
(Digital)
 Battery sensor
1.
Wiring faulty
15

Parking brake
 C-CAN
 IPM
ABS
1.
CAN line faulty
16

Door open
 C-CAN
 BCM
1.
CAN line faulty
17

Water separator
 Hardwire
(Digital)
 Fuel water separator sensor
1.
Wiring faulty
18

Key out
 C-CAN
 SMK
1.
CAN line faulty
19

DBC
 C-CAN
 TCS
1.
CAN line faulty
20

Check engine
 C-CAN
 EMS
1.
CAN line faulty
21

Glow
 C-CAN
 EMS
1.
CAN line faulty
22

VDC(ESC)
 C-CAN
 TCS
1.
CAN line faulty
23

VDC OFF
(ESC OFF)
 C-CAN
 TCS
1.
CAN line faulty
24

ABS
 C-CAN
 ABS
TCS
1.
CAN line faulty
25

Trunk open
 C-CAN
 IPM
1.
CAN line faulty
26

Immobilizer
 C-CAN
 SMK
1.
CAN line faulty
27

Low fuel
 Hardwire
(Analogue)
 Fuel sender
1.
Fuel sender faulty
2.
Wiring faulty
28

Washer low
 Hardwire
(Digital)
 Washer fluid level sensor
1.
Wiring faulty
29

TPMS(TREAD)
 C-CAN
 TPMS
1.
CAN line faulty
30

4WD
 C-CAN
 4WD
1.
CAN line faulty
31

4WD Lock
 C-CAN
 4WD
1.
CAN line faulty
32

EPS
 C-CAN
 MDPS
1.
CAN line faulty
33

LDWS
 C-CAN
 LDWS
1.
CAN line faulty

2.
Check the suspected area as below table when the gauge is error.
NO
 Description
 Communication
 Signal (Unit/Sensor)
 Suspected Area
1
 Speedometer
 C-CAN
 TCU
1.
CAN line faulty
3
 Tachometer
 C-CAN
 EMS
1.
CAN line faulty
4
 Coolant temperature
 C-CAN
 EMS
1.
CAN line faulty
5
 Fuel level
 Hardwire
 Fuel sender
1.
Fuel sender faulty
2.
Wiring faulty
6
 Shift indicator
 C-CAN
 TCU
1.
CAN line faulty

3.
Check the specified value of cluster connector in specified condition.
NO
 Description
 Input/
Output
 Communication
 Value
 Specified conditions
A1
 Airbag supply
 Input
 Hardwire
 9~16
 IGN Switch ON
A2
 P output
 Output
 Hardwire
 6 ~ 15
 IGN ON & shift the lever in P
A3
 R Output
 Output
 Hardwire
 6 ~ 15
 IGN ON & shift the lever in R
A4
 N Output
 Output
 Hardwire
 6 ~ 15
 IGN ON & shift the lever in N
A5
 D Output
 Output
 Hardwire
 6 ~ 15
 IGN ON & shift the lever in D
A6
 Rheostat Detent
 Output
 Hardwire
 6 ~ 15
 IGN ON & rheostat up to max position
A7
 Fuel
 Input
 Hardwire
 ~1.3
 Gauge is FULL
7.68~
 Gauge is EMPTY
A8
 -
 　
 　
 　
 　
A9
 Water separator sensor
 Input
Instrument Cluster Installation
1. Connect the cluster connector. 2. Install the cluster assembly. 3. Install the cluster facia panel. ...

Troubleshooting
Symptom Possible cause Remedy Speedometer does not operate Cluster fuse (10A) blown Check for short and replace fuse Speedometer faulty ...

See also:

Component Location
1. Overdrive Clutch (OD/C) 2. One way Clutch (OWC) 3. Low & Reverse Brake (LR/B) 4. Underdrive Brake (UD/B) 5. 26 Brake(26/B) 6. 35R Clutch (35R/C) 7. Damper Clu ...

External Amplifier Components
Connector Pin Information No. Connector A (26 pin) Connector B (16 pin) Connector C (12 pin) 1 Battery + Right surround speaker + ...

Side Airbag (SAB) Module Installation
   Be sure to install the harness wires not to be pinched or interfered with other parts. ...

Categories

Copyright www.ksmanual.com 2014-2026