Kia Sorento: Cup holder. Seat warmer: (if equipped) - Interior features - Controls and FeaturesKia Sorento: Cup holder. Seat warmer: (if equipped)

Kia Sorento (MQ4, 2021-2026) Owner's Manual / Controls and Features / Interior features / Cup holder. Seat warmer: (if equipped)

Cup holder

Front center console cup holders layout in the Kia Sorento cabin
Rear passenger armrest cup holder compartment in the Kia Sorento
Retractable cup holder mechanisms integrated into the Kia Sorento interior trim
Door panel integrated beverage bottle holders in the Kia Sorento

You may place standard cups, travel mugs, or small beverage cans securely in the dedicated cup holders designed throughout the cabin of your Kia Sorento.

WARNING: Hot Liquids Safety

Do not place uncovered containers filled with hot liquids into the cup holders while the vehicle is in motion. Sudden acceleration, braking, or turning maneuvers could cause hot liquid to spill, resulting in severe burns to vehicle occupants. Furthermore, a driver suffering from sudden burns could easily lose control of the Kia Sorento, leading to a dangerous traffic accident.

WARNING: Pressurized Containers

Always keep canned or bottled beverages protected from direct sunlight, and never leave pressurized containers inside a parked vehicle exposed to high ambient temperatures. Under extreme heat buildup, these containers can rupture or explode.

NOTE

Seat warmer: (if equipped)

The integrated seat warmer system provides rapid and adjustable thermal comfort for vehicle occupants during chilly weather conditions in your Kia Sorento.

Figure 1. Front seat
Front seat heater control buttons and ergonomic cushioning in the Kia Sorento
Figure 2. Rear seat
Rear passenger row seat warmer activation switch in the Kia Sorento

With the ENGINE START/STOP ignition button switched to the ON position:

During mild weather seasons or whenever seat heating is unnecessary, keep the control switches turned off to conserve vehicle electrical power.

To protect against unintended operation, the seat warmer system automatically defaults to the OFF state every time the ENGINE START/STOP button is cycled ON.

Temperature control (manual)

Temperature control (automatic)

To prevent low-temperature burns following manual activation on the high setting, the seat warmer automatically steps down its thermal output over time according to a pre-programmed schedule:

Temperature

Duration

OFF

-

High

30 minutes

Medium

60 minutes

Low

-

You can manually press the button again to increase the seat temperature if desired; however, the system will revert to its managed automatic regulation profile after a brief operational period.

To turn off the seat warmer immediately at any time, press and hold the control button for more than 1.5 seconds.

TIP: When the seat warmer controls are active, the internal heating grid cycles on and off automatically based on real-time surface temperature feedback to maintain optimal thermal comfort inside the Kia Sorento.

CAUTION

WARNING: Seat Warmer Burn Hazard

Passengers must exercise extreme care when utilizing seat warmers, as prolonged exposure to elevated temperatures can cause thermal burns even at relatively low heat settings. The driver must maintain heightened vigilance when operating seat warmers for vulnerable individuals:

  1. Infants, young children, elderly passengers, individuals with physical disabilities, or hospital patients

  2. Persons with delicate, sensitive skin or those prone to easy thermal blistering

  3. Extremely fatigued or exhausted individuals

  4. Intoxicated passengers

  5. Individuals taking prescription medications that induce drowsiness, deep sleep, or reduced sensory perception (such as sleeping pills or heavy cold medications)

Interior features
A wide array of refined comfort and utility features are built into the cabin of the Kia Sorento to elevate the travel experience for every occupant....
Air ventilation seat: (if equipped). Sun visor
Air ventilation seat: (if equipped) The airflow intensity and cooling ventilation leve...
See also:

Rear Hub - Carrier Disassembly
1. Remove the hub assembly mounting bolts (A-4ea) from the rear axle carrier (B). Tightening torque: 78.5 ~ 88.3N.m (8.0 ~ 9.0 ...

Checking the washer fluid level
The reservoir is translucent so that you can check the level with a quick visual inspection. Check the fluid level in the washer fluid reservoir and add fluid if necessary. Plain water may be use ...

AUX(Auxiliary) Jack Description
The AUX, iPod and USB JACK on the center console is for customers who like to listen to external portable music players like the MP3, iPod, earphone, USB memory stick, CD player and etc., thr ...

Copyright © www.ksmanual.com 2014-2026 - 0.0286