Kia Sorento: Input/Output Specification - IMS (Integrated Memory) - Body Electrical System - Kia Sorento XM 2011-2019 Service ManualKia Sorento: Input/Output Specification

Second Generation XM (2011-2019) / Kia Sorento XM 2011-2019 Service Manual / Body Electrical System / IMS (Integrated Memory) / Input/Output Specification

Connector Pin Lay Out

IMS input/output pin information
No
Signal Name
I/O
Contents
Remark
A1
-
-
-

A2
FR height motor up
O
FR height motor up output

A3
RR height motor up
O
RR height motor up output

A4
Recline motor FR
O
Recline motor FR output

A5
Slide motor FR
O
Slide motor FR output

A6
-
-
-

A7
FR height motor down
O
FR height motor down output

A8
-
-
-

A9
-
-
-

A10
RR height motor down
O
RR height motor down output

A11
Recline motor RR
O
Recline motor RR output

A12
Slide motor RR
O
Slide motor RR output

B1
GND (Power)
I
Power GND for operating motor

B2
-
-
-

B3
B+ (Power)
I
Power B+ for operating motor

B4
GND (Power)
I
Power GND for operating motor

B5
B+ (Power)
I
Power B+ for operating motor

C1
-
-
-

C2
-
-
-

C3
Slide FR manual switch
I
Slide FR manual switch input
On : GND
C4
Recline FR manual switch
I
Recline FR manual switch input
On : GND
C5
FR height up manual switch
I
FR height up manual switch input
On : GND
C6
RR height up manual switch
I
RR height up manual switch input
On : GND
C7
Slide motor sensor
I
Slide motor sensor input
Pulse signal
C8
Recline motor sensor
I
Recline motor sensor input
Pulse signal
C9
FR height motor sensor
I
FR height motor sensor input
Pulse signal
C10
Sensor Vcc(Seat)
O
VCC for operating sensor
5V
C11
-
-
-

C12
-
-
-

C13
Slide RR manual switch
I
Slide RR manual switch input
ON : GND
C14
Recline RR manual switch
I
Recline RR manual switch input
ON : GND
C15
FR height down manual switch
I
FR height down manual switch input
ON : GND
C16
RR height down manual switch
-
RR height down manual switch input
ON : GND
C17
-
-
-

C18
-
-
-

C19
-
-
-

C20
-
-
-

D1
-
-
-

D2
RR height up sensor
I
RR height up motor sensor
Pulse signal
D3
-
-
-

D4
LIN
I/O
LIN

D5
-
-
-

D7
IGN2
I
IGN2 input
BAT
D8
B+(ECU)
I
ECU power input
BAT
D9
GND(ECU)
I
ECU GND

D10
-
-
-

D11
-
-
-

D12
-
-
-

D13
"P" position
I
"P" position switch input
ON : GND
D14
-
-
-

D15
-
-
-

D16
-
-
-


Circuit Diagram
...

Communication System
...

See also:

AC Inverter Unit Removal
1. Disconnect the negative (-) battery terminal. 2. Remove the right luggage side trim. (Refer to Body - "Luggage Side Trim") ...

Inspection
1. Disconnect the ignition switch connector (B) and key warning switch connector (A) from under the steering column. 2. Che ...

Rear Body
* These dimensions indicated in this figure are actual-measurement dimensions. [ Unit : mm (inch) ] Side outer p ...

Copyright © www.ksmanual.com 2014-2019