Kia Optima Manuals

Kia Sorento: Timing Chain Installation - Timing System - Engine Mechanical System - Kia Sorento XM 2011-2026 Service ManualKia Sorento: Timing Chain Installation

Second Generation XM (2011-2026) / Kia Sorento XM 2011-2026 Service Manual / Engine Mechanical System / Timing System / Timing Chain Installation

1.
Install the balance shaft chain.
(Refer to Lubrication system - "Balance Shaft & Oil Pump")
2.
Install the crankshaft chain sprocket (B) and the timing chain oil jet (A).
Tightening torque:
7.8 ~ 9.8 N.m (0.8 ~ 1.0 kgf.m, 5.8 ~ 7.2 lb-ft)

3.
Set the crankshaft so that the key (A) of crankshaft will be aligned with the mating surface of main bearing cap. Put the intake and exhaust camshaft assembly so that the TDC marks (B) of the intake and exhaust CVVT sprockets will be aligned with the top surface of cylinder head. As a result of this, the piston of No.1 cylinder is placed at the top dead center on compression stroke.
4.
Install the timing chain guide (A).
Tightening torque:
9.8 ~ 11.8 N.m (1.0 ~ 1.2 kgf.m, 7.2 ~ 8.7 lb-ft)

5.
Install the timing chain. To install the timing chain with no slack between each shaft (cam, crank), follow the below procedure.
Crankshaft sprocket (A) → Timing chain guide (B) → Intake CVVT sprocket (C) → Exhaust CVVT sprocket (D).

  
The timing marks of each sprocket should be matched with timing marks (color link) of timing chain when installing the timing chain.

6.
Install the timing chain tensioner arm (A).
Tightening torque:
9.8 ~ 11.8 N.m (1.0 ~ 1.2 kgf.m, 7.2 ~ 8.7 lb-ft)

7.
Install the timing chain auto tensioner (B) and remove the stopper pin (A).
Tightening torque:
9.8 ~ 11.8 N.m (1.0 ~ 1.2 kgf.m, 7.2 ~ 8.7 lb-ft)

8.
After rotating crankshaft 2 revolutions in regular direction (clockwise viewed from front), confirm that the TDC marks (A) on the intake and exhaust CVVT sprockets aligned with the top surface of cylinder head.

9.
Install the timing chain cover.
(Refer to Timing System - "Timing Chain Cover")
10.
Install cylinder head cover.
(Refer to Cylinder Head Assembly - "Cylinder Head Cover")
11.
Add all the necessary fluids and check for leaks. Connect GDS. Check for codes, note, and clear. Recheck.
  
•
Refill engine with engine oil.
•
Refill a transaxle with fluid.
•
Refill a radiator and a reservoir tank with engine coolant.
•
Clean battery posts and cable terminals and assemble.
•
Inspect for fuel leakage.
-
After assemble the fuel line, turn on the ignition switch (do not operate the starter) so that the fuel pump runs for approximately two seconds and fuelline pressurizes.
-
Repeat this operation two or three times, then check for fuel leakage at any point in the fuel line.
•
Refill radiator and reservoir tank with engine coolant.
•
Bleed air from the cooling system.
Timing Chain Inspection
Sprockets, Hydraulic Tensioner, Chain Guide, Tensioner Arm, Timing Chain 1. Check the CVVT sprocket, crankshaft sprocket teeth for abnormal wear, cracks or damage. Replace ...

Cylinder Head Assembly
...

See also:

Rear Air Conditioner Unit Replacement
1. Disconnect the negative (-) battery terminal. 2. Recover the refrigerant with a recover/recycling/charging station. 3. ...

Using Bluetooth® Wireless Technology
Phone Menu Screen Phone Menus With a Bluetooth® Wireless Technology device connected, press the key to display the Phone menu screen. 1) Favorite : Up to 20 frequently used contacts saved f ...

AC Inverter Oultet Installation
1. Install the power outlet switch. 2. Install the rear console cover. 3. Connect the negative (-) battery term ...

Categories

Copyright www.ksmanual.com 2014-2026