Kia Sorento: Specification
| Items |
Inner side |
Outer side |
||
| Front driveshaft |
2.4GDI M/T |
Joint type |
LSJ 104 |
UBJ 104 |
| Max. permissible angle |
23° |
50° |
||
| 2.4GDI A/T |
Joint type |
LSJ 100 |
UBJ 100 |
|
| Max. permissible angle |
23° |
50° |
||
| 3.3GDI A/T |
Joint type |
LSJ 104 |
UBJ 104 |
|
| Max. permissible angle |
23° |
50° |
||
| Rear driveshaft |
Joint type |
EDJ 82 |
EBJ 82 |
|
| Max. permissible angle |
|
|
||
| Rear differential |
Oil type |
Hypoid gear oil, MS 517-15 GT (SAE 75W/90, API GL-5, SHELL SPIRAX X) |
||
| Oil capacity (L) |
0.53±0.05 |
|||
| Reduction gear type |
Hypoid gear |
|||
| Reduction gear ratio |
2.533 |
|||
| Final drive gear backlash mm(in.) |
0.07 ~ 0.15 |
|||
| Differential gear backlash mm(in.) |
0 ~ 0.05 |
|||
Tightening torques
| Items |
Nm |
Kgf-m |
lb-ft |
|
| Front |
Wheel nut |
88.3 ~ 107.9 |
9.0 ~ 11.0 |
65.1 ~ 79.6 |
| Driveshaft nut |
240.3 ~ 269.7 |
24.5 ~ 27.5 |
177.2 ~ 198.9 |
|
| Strut assembly lower mounting bolt |
156.9 ~ 176.5 |
16.0 ~ 18.0 |
115.7 ~ 130.1 |
|
| Inner shaft bearing bracket bolt |
49.0 ~ 68.6 |
5.0 ~ 7.0 |
36.1 ~ 50.6 |
|
| Break caliper mounting bolt |
78.4 ~ 98.0 |
8.0 ~ 10.0 |
57.8 ~ 72.3 |
|
| Wheel speed sensor mounting bolt |
6.9 ~ 10.8 |
0.7 ~ 1.1 |
5.1 ~ 8.0 |
|
| Break disc mounting screw |
4.9 ~ 5.9 |
0.5 ~ 0.6 |
3.6 ~ 4.3 |
|
| Lower arm ball joint mounting bolt |
98.1 ~ 117.7 |
10.0 ~ 12.0 |
72.3 ~ 86.8 |
|
| Tie rod end ball joint mounting nut |
23.5 ~ 33.3 |
2.4 ~ 3.4 |
17.3 ~ 24.5 |
|
| Rear |
Wheel nut |
88.3 ~ 107.9 |
9.0 ~ 11.0 |
65.1 ~ 79.6 |
| Driveshaft castle nut |
240.3 ~ 269.7 |
24.5 ~ 27.5 |
177.2 ~ 198.9 |
|
| Shock absorber upper mounting bolt |
137.3 ~ 156.9 |
10.0 ~ 12.0 |
101.3 ~ 115.7 |
|
| Shock absorber lower mounting nut |
137.2 ~ 156.9 |
14.0 ~ 16.0 |
101.2 ~ 115.7 |
|
| Break caliper mounting bolt |
63.7 ~ 73.5 |
6.5 ~ 7.5 |
47.0 ~ 54.2 |
|
| Wheel speed sensor mounting bolt |
6.9 ~ 10.8 |
0.7 ~ 1.1 |
5.1 ~ 8.0 |
|
| Break disc mounting screw |
4.9 ~ 5.9 |
0.5 ~ 0.6 |
3.6 ~ 4.3 |
|
| Hub assembly mounting bolt |
78.4 ~ 98.0 |
8.0 ~ 10.0 |
57.9 ~ 72.3 |
|
| Upper arm mounting nut (to knuckle) |
2WD : 137.2 ~ 156.9 |
14.0 ~ 16.0 |
101.2 ~ 115.7 |
|
| 4WD : 98.1 ~ 117.7 |
10.0 ~ 12.0 |
72.3 ~ 86.8 |
||
| Lower arm mounting bolt |
137.3 ~ 156.9 |
14.0 ~ 16.0 |
101.3 ~ 115.7 |
|
| Assist arm ball joint mounting nut |
44.1 ~ 53.9 |
4.5 ~ 5.5 |
32.5 ~ 39.8 |
|
| Parking cable mounting nut |
6.9 ~ 10.8 |
0.7 ~ 1.1 |
5.1 ~ 8.0 |
|
| Trailing arm mounting bolt |
44.1 ~ 53.9 |
4.5 ~ 5.5 |
32.5 ~ 39.8 |
|
| Propeller shaft |
Propeller shaft mounting bolt |
49.0 ~ 68.6 |
5.0 ~ 7.0 |
36.2 ~ 50.6 |
| Propeller shaft center bearing bracket mounting bolt |
49.0 ~ 68.6 |
5.0 ~ 7.0 |
36.2 ~ 50.6 |
|
| Rear propeller shaft mounting bolt |
49.0 ~ 68.6 |
5.0 ~ 7.0 |
36.2 ~ 50.6 |
|
| Differential |
Rear differential mounting bolt |
68.6 ~ 88.3 |
7.0 ~ 9.0 |
50.6 ~ 65.1 |
| Differential cover mounting bolt |
68.6 ~ 88.3 |
7.0 ~ 9.0 |
50.6 ~ 65.1 |
|
| Differential gear drain plug |
49.0 ~ 68.6 |
5.0 ~ 7.0 |
36.2 ~ 50.6 |
|
Lubricants
Items
Lubricants
Quantity (g)
Front driveshaft
LSJ 104
SH06-VX21
240 ~ 255
UBJ 104
RBA
165 ~ 175
LSJ 100
...
See also:
Interior C
* These dimensions indicated in this figure are actual-measurement
dimensions. [ Unit : mm (inch) ]
...
Line Pressure Control Solenoid Valve
line pressure control solenoid valve is attached to the valve body. This
variable force solenoid valve directly controls the hydraulic pressure inside
the line pressure.
...
CVVT & Camshaft Installation
1.
Install the intakeCVVT assembly(A), exhaust CVVT assembly(B) and camshaft(C).
Tightening torque :
53.9 ~ 63.7 N.m (5.5 ~ 6.5 kgf.m, 39 ...
Copyright © www.ksmanual.com 2014-2024