Kia Sorento: Rear Shock Absorber Removel
1. |
Remove the rear wheel and tire (A) from rear hub .
Tightening torque:
88.2 ~ 107.8 N.m (9.0 ~ 11.0 kgf.m, 65.0 ~ 79.5 lb-ft)
|
Be careful not to damage to the hub bolts when removing
the rear wheel and tire (A).
|
|
2. |
Support the rear lower arm (A) with a jack as shown in the illustration.
Certainly install Jack as being danger because of the
tension.
|
|
3. |
Loosen the bolt (A-1ea) and then remove the rear shock absorber
cover (B).
Tightening torque:
5.9 ~ 9.8 N.m (0.6 ~ 1.0 kgf.m, 4.3 ~ 7.2 lb-ft)
|
|
4. |
Remove the rear wheel guard.
(Refer to Body (Interior and Exterior) - "Rear Wheel Guard")
|
5. |
Loosen the bolt (A,B) & nut (C) and then remove the rear shock
absorber bracket (D).
Tightening torque:
Bolts :
(A) 137.3 ~ 159.9N.m (14.0 ~ 16.0kgf.m, 101.3 ~ 115.7lb-ft)
(B) 88.2 ~ 107.8 N.m (9.0 ~ 11.0 kgf.m, 65.0 ~ 79.5 lb-ft)
Nuts :
(C) 88.2 ~ 107.8 N.m (9.0 ~ 11.0 kgf.m, 65.0 ~ 79.5 lb-ft)
|
|
6. |
Loosen the nut (A) and then remove the rear shock absorber (B).
Tightening torque:
137.3 ~ 159.9N.m (14.0 ~ 16.0kgf.m, 101.3 ~ 115.7lb-ft)
|
|
1. |
Remove the rear wheel and tire (A) from rear hub .
Tightening torque:
88.2 ~ 107.8 N.m (9.0 ~ 11.0 kgf.m, 65.0 ~ 79.5 lb-ft)
|
Be careful not to damage to the hub bolts when removing
the rear wheel and tire (A).
|
|
2. |
Support the rear lower arm (A) with a jack as shown in the illustration.
Risk due to the spring tension to Honor Jack definitely
fixed.
|
|
3. |
Loosen the bolt (A-1ea) and then remove the rear shock absorber
cover (B).
Tightening torque:
5.9 ~ 9.8 N.m (0.6 ~ 1.0 kgf.m, 4.3 ~ 7.2 lb-ft)
|
|
4. |
Loosen the bolt (A) & nut (B) and then remove the rear shock absorber
(C).
Tightening torque:
Bolt (A) : 137.3
~ 159.9N.m (14.0 ~ 16.0kgf.m, 101.3 ~ 115.7lb-ft)
Nut (B) : 137.3
~ 159.9N.m (14.0 ~ 16.0kgf.m, 101.3 ~ 115.7lb-ft)
|
|
2WD
1. Rear upper arm
2. Rear stabilizer bar
3. Rear lower arm
4. Rear assist arm
5. Rear shock absorber
6. Rear cross member
7. Trailing arm
...
1.
Check the rubber parts for damage or deterioration.
2.
Check the shock absorber for abnormal resistance or unusual sounds.
...
See also:
Parking Assist Sensor Removal
1.
Disconnect the negative (-) battery terminal.
2.
Remove the rear bumper cover.
(Refer to Body - "Rear Bumper Cover")
...
Rear Differential Carrier Reassembly
Pinion drive gear height adjustment
Adjust the height of the drive pinion in the following order.
1.
Below are the special tools to measure the pinion height
...
Climate control air filter (if equipped)
The climate control air filter installed behind the glove box filters the dust
or other pollutants that come into the vehicle from the outside through the heating
and air conditioning system.
If ...