Kia Optima Manuals

Kia Sorento: Engine Mounting Removal and Installation - Engine And Transmission Assembly - Engine Mechanical System - Kia Sorento XM 2011-2024 Service ManualKia Sorento: Engine Mounting Removal and Installation

Second Generation XM (2011-2024) / Kia Sorento XM 2011-2024 Service Manual / Engine Mechanical System / Engine And Transmission Assembly / Engine Mounting Removal and Installation

Roll road Bracket

1.
Remove the roll road bracket(A).
Tightening torque
Bolt (B) :
49.0 ~ 63.7 N.m (5.0 ~ 6.5 kgf.m, 36.2 ~ 47.0 lb-ft)
Bolt (C) :
107.9 ~ 127.5 N.m (11.0 ~ 13.0 kgf.m, 79.6 ~ 94.0 lb-ft)

2.
Install in the reverse order of removal.

Engine Mounting Bracket

1.
Install the jack to the edge of upper oil pan to support the engine.
  
Insert the rubber block between jack and oil pan.
2.
Disconnect the ground cable (A), and then remove the engine mounting support bracket (B).
Tightening torque
Ground line bolt :
10.8 ~ 13.7 N.m (1.1 ~ 1.4 kgf.m, 8.0 ~ 10.1 lb-ft)
Nut and bolt :
88.3 ~ 107.9 N.m (9.0 ~ 11.0 kgf.m, 65.1 ~ 79.6 lb-ft)

3.
Remove the reservoir tank.
(Refer to Cooling System - "Reservoir Tank")
4.
Remove the engine mounting bracket(A).
Tightening torque :
63.7 ~ 83.3 N.m (6.5 ~ 8.5 kgf.m, 47.0 ~ 61.5 lb-ft)

5.
Install in the reverse order of removal.

Transaxle Mounting Bracket

1.
Remove the air duct.
(Refer to Intake and Exhaust System - "Air Cleaner")
2.
Remove the battery and tray.
(Refer to Engine Electrical System - "Battery")
3.
Remove the air cleaner assembly.
(Refer to Intake and Exhaust System - "Air Cleaner")
4.
Install the jack to the edge of transaxle.
5.
Disconnect the ground cable(A).
Tightening torque :
10.8 ~ 13.7 N.m (1.1 ~ 1.4 kgf.m, 8.0 ~ 10.1 lb-ft)

6.
Remove the service cover(A).
7.
Remove the transaxle mounting bolts(A).
Tightening torque :
88.3 ~ 107.9 N.m (9.0 ~ 11.0 kgf.m, 65.1 ~ 79.6 lb-ft)

8.
Remove the transaxle mounting bracket(A).
Tightening torque :
63.7 ~ 83.3 N.m (6.5 ~ 8.5 kgf.m, 47.0 ~ 61.5 lb-ft)

9.
Install in the reverse order of removal.
Engine Mounting Components
1. Transaxle mounting bracket 2. Roll rod bracket 3. Engine mounting bracket 4. Engine mounting support bracket ...

Engine And Transmission Assembly Removal
   • Use fender covers to avoid damaging painted surfaces. • ...

See also:

Circuit Diagram
Connector Pin Information No. Wire harness connector Panorama motor Blind motor 1 Ground 1 ...

Troubleshooting
Trouble Symptom Probable cause Remedy Vehicle pulls to one side Scoring of driveshaft ball joint Replace Wear, rattle or scoring of wheel b ...

Side Airbag (SAB) Module Components
...

Categories


Copyright © www.ksmanual.com 2014-2024