Kia Sorento: Specification
| Items |
Inner side |
Outer side |
||
| Front driveshaft |
2.4GDI M/T |
Joint type |
LSJ 104 |
UBJ 104 |
| Max. permissible angle |
23° |
50° |
||
| 2.4GDI A/T |
Joint type |
LSJ 100 |
UBJ 100 |
|
| Max. permissible angle |
23° |
50° |
||
| 3.3GDI A/T |
Joint type |
LSJ 104 |
UBJ 104 |
|
| Max. permissible angle |
23° |
50° |
||
| Rear driveshaft |
Joint type |
EDJ 82 |
EBJ 82 |
|
| Max. permissible angle |
|
|
||
| Rear differential |
Oil type |
Hypoid gear oil, MS 517-15 GT (SAE 75W/90, API GL-5, SHELL SPIRAX X) |
||
| Oil capacity (L) |
0.53±0.05 |
|||
| Reduction gear type |
Hypoid gear |
|||
| Reduction gear ratio |
2.533 |
|||
| Final drive gear backlash mm(in.) |
0.07 ~ 0.15 |
|||
| Differential gear backlash mm(in.) |
0 ~ 0.05 |
|||
Tightening torques
| Items |
Nm |
Kgf-m |
lb-ft |
|
| Front |
Wheel nut |
88.3 ~ 107.9 |
9.0 ~ 11.0 |
65.1 ~ 79.6 |
| Driveshaft nut |
240.3 ~ 269.7 |
24.5 ~ 27.5 |
177.2 ~ 198.9 |
|
| Strut assembly lower mounting bolt |
156.9 ~ 176.5 |
16.0 ~ 18.0 |
115.7 ~ 130.1 |
|
| Inner shaft bearing bracket bolt |
49.0 ~ 68.6 |
5.0 ~ 7.0 |
36.1 ~ 50.6 |
|
| Break caliper mounting bolt |
78.4 ~ 98.0 |
8.0 ~ 10.0 |
57.8 ~ 72.3 |
|
| Wheel speed sensor mounting bolt |
6.9 ~ 10.8 |
0.7 ~ 1.1 |
5.1 ~ 8.0 |
|
| Break disc mounting screw |
4.9 ~ 5.9 |
0.5 ~ 0.6 |
3.6 ~ 4.3 |
|
| Lower arm ball joint mounting bolt |
98.1 ~ 117.7 |
10.0 ~ 12.0 |
72.3 ~ 86.8 |
|
| Tie rod end ball joint mounting nut |
23.5 ~ 33.3 |
2.4 ~ 3.4 |
17.3 ~ 24.5 |
|
| Rear |
Wheel nut |
88.3 ~ 107.9 |
9.0 ~ 11.0 |
65.1 ~ 79.6 |
| Driveshaft castle nut |
240.3 ~ 269.7 |
24.5 ~ 27.5 |
177.2 ~ 198.9 |
|
| Shock absorber upper mounting bolt |
137.3 ~ 156.9 |
10.0 ~ 12.0 |
101.3 ~ 115.7 |
|
| Shock absorber lower mounting nut |
137.2 ~ 156.9 |
14.0 ~ 16.0 |
101.2 ~ 115.7 |
|
| Break caliper mounting bolt |
63.7 ~ 73.5 |
6.5 ~ 7.5 |
47.0 ~ 54.2 |
|
| Wheel speed sensor mounting bolt |
6.9 ~ 10.8 |
0.7 ~ 1.1 |
5.1 ~ 8.0 |
|
| Break disc mounting screw |
4.9 ~ 5.9 |
0.5 ~ 0.6 |
3.6 ~ 4.3 |
|
| Hub assembly mounting bolt |
78.4 ~ 98.0 |
8.0 ~ 10.0 |
57.9 ~ 72.3 |
|
| Upper arm mounting nut (to knuckle) |
2WD : 137.2 ~ 156.9 |
14.0 ~ 16.0 |
101.2 ~ 115.7 |
|
| 4WD : 98.1 ~ 117.7 |
10.0 ~ 12.0 |
72.3 ~ 86.8 |
||
| Lower arm mounting bolt |
137.3 ~ 156.9 |
14.0 ~ 16.0 |
101.3 ~ 115.7 |
|
| Assist arm ball joint mounting nut |
44.1 ~ 53.9 |
4.5 ~ 5.5 |
32.5 ~ 39.8 |
|
| Parking cable mounting nut |
6.9 ~ 10.8 |
0.7 ~ 1.1 |
5.1 ~ 8.0 |
|
| Trailing arm mounting bolt |
44.1 ~ 53.9 |
4.5 ~ 5.5 |
32.5 ~ 39.8 |
|
| Propeller shaft |
Propeller shaft mounting bolt |
49.0 ~ 68.6 |
5.0 ~ 7.0 |
36.2 ~ 50.6 |
| Propeller shaft center bearing bracket mounting bolt |
49.0 ~ 68.6 |
5.0 ~ 7.0 |
36.2 ~ 50.6 |
|
| Rear propeller shaft mounting bolt |
49.0 ~ 68.6 |
5.0 ~ 7.0 |
36.2 ~ 50.6 |
|
| Differential |
Rear differential mounting bolt |
68.6 ~ 88.3 |
7.0 ~ 9.0 |
50.6 ~ 65.1 |
| Differential cover mounting bolt |
68.6 ~ 88.3 |
7.0 ~ 9.0 |
50.6 ~ 65.1 |
|
| Differential gear drain plug |
49.0 ~ 68.6 |
5.0 ~ 7.0 |
36.2 ~ 50.6 |
|
Lubricants
Items
Lubricants
Quantity (g)
Front driveshaft
LSJ 104
SH06-VX21
240 ~ 255
UBJ 104
RBA
165 ~ 175
LSJ 100
...
See also:
Rear Lower Arm Removal
1.
Remove the rear wheel and tire (A) from rear hub .
Tightening torque :
88.2 ~ 107.8 N.m (9.0 ~ 11.0 kgf.m, 65.0 ~ 79.5 lb-ft)
...
Circuit Diagram
...
Instrument Cluster Installation
1.
Connect the cluster connector.
2.
Install the cluster assembly.
3.
Install the cluster facia panel.
...
Copyright © www.ksmanual.com 2014-2024