Kia Sorento: Troubleshooting - Lighting System - Body Electrical System - Kia Sorento XM 2011-2024 Service ManualKia Sorento: Troubleshooting

Second Generation XM (2011-2024) / Kia Sorento XM 2011-2024 Service Manual / Body Electrical System / Lighting System / Troubleshooting

Symptom
Possible cause
Remedy
One lamp does not light
(all exterior)
Bulb burned out
Replace bulb
Socket, wiring or ground faulty
Repair if necessary
Head lamps do not light
Bulb burned out
Replace bulb
Ignition fuse (LOW:10A, HIGH:20A) blown
Check for short and replace fuse
Head lamp fuse (15A) blown
Check for short and replace fuse
Head lamp relay faulty
Check relay
Lighting switch faulty
Check switch
Wiring or ground faulty
Repair if necessary
Tail lamps and license plate lamps do not light
Bulb burned out
Replace bulb
Tail lamp fuse (10A) blown
Check for short and replace fuse
Tail lamp relay faulty
Check relay
Lighting switch faulty
Check switch
Wiring or ground faulty
Repair if necessary
Stop lamps do not light
Bulb burned out
Replace bulb
Stop lamp fuse (15A) blown
Check for short and replace fuse
Stop lamp switch faulty
Adjust or replace switch
Wiring or ground faulty
Repair if necessary
Stop lamps do not turn off
Stop lamp switch faulty
Repair or replace switch
Instrument lamps do not light
(Tail lamps light)
Rheostat faulty
Check rheostat
Wiring or ground faulty
Repair if necessary
Turn signal lamp does not flash on one side
Bulb burned out
Replace bulb
Turn signal switch faulty
Check switch
Wiring or ground faulty
Repair if necessary
Turn signal lamps do not light
Bulb burned out
Replace bulb
Turn signal lamp fuse (10A) blown
Check for short and replace fuse
Flasher unit faulty
Check flasher unit
Turn signal switch faulty
Check switch
Wiring or ground faulty
Repair if necessary
Hazard warning lamps do not light
Bulb burned out
Replace bulb
Hazard warning lamp fuse (15A) blown
Check for short and replace fuse
Flasher unit faulty
Check flasher unit
Hazard switch faulty
Check switch
Wiring or ground faulty
Repair if necessary
Flasher rate too slow or too fast
Lamps' wattages are smaller or larger than specified
Replace lamps
Flasher unit faulty
Check flasher unit
Back up lamps do not light
Bulb burned out
Replace bulb
Back up lamp fuse (10A) blown
Check for short and replace fuse
Back up lamp switch (M/T) faulty
Check switch
Transaxle range switch (A/T) faulty
Check switch
Wiring or ground faulty
Repair if necessary
Room lamp does not light
Bulb burned out
Replace bulb
Room lamp fuse (10A) blown
Check for short and replace fuse
Room lamp switch faulty
Check switch
Wiring or ground faulty
Repair if necessary
Front fog lamps do not light
Bulb burned out
Replace bulb
Front fog lamp fuse (15A) blown
Check for short and replace fuse
Front fog lamp relay faulty
Check relay
Front fog lamp switch faulty
Check switch
Wiring or ground faulty
Repair if necessary
Rear fog lamp fuse (15A) blown
Check for short and replace fuse
Rear fog lamp fuse (15A) blown
Check for short and replace fuse
Rear fog lamp switch faulty
Check switch
Rear fog lamp relay faulty
Check relay
Wiring or ground faulty
Repair if necessary
Map lamp does not light
Bulb burned out
Replace bulb
Room lamp fuse (10A) blown
Check for short and replace fuse
Map lamp switch faulty
Check switch
Wiring or ground faulty
Repair if necessary
Trunk room lamp does not light
Bulb burned out
Replace bulb
Room lamp fuse (10A) blown
Check for short and replace fuse
Trunk room lamp switch faulty
Check switch
Wiring or ground faulty
Repair if necessary

Rear combination lamp Installation
1. Install the tailgate combination lamp assembly after replacing the bulb. 2. Install the lamp cover to the tailgate after connecting the ...

Auto Lighting Control System
...

See also:

Inspection
1. Turn the ignition switch OFF. 2. Disconnect the PCSV connector. 3. Measure resistance between the PCSV termi ...

Balance Shaft & Oil Pump Installation
BSM(Balance Shaft Module) Chain System 1. The key of crankshaft should be aligned with the mating face of main bearing cap. As a result of this, the piston of No.1 cylinde ...

Changing tires
1.Park on a level surface and apply the parking brake firmly. 2.Place the transaxle shift lever in R (Reverse) with manual transaxle or P (Park) with automatic transaxle. 3.Activate the hazard wa ...

Copyright В© www.ksmanual.com 2014-2024