Kia Sorento: Specifications - Engine Control / Fuel System - Kia Sorento XM 2011-2019 Service ManualKia Sorento: Specifications

Second Generation XM (2011-2019) / Kia Sorento XM 2011-2019 Service Manual / Engine Control / Fuel System / Specifications

Fuel Delivery System
Items
Specification
Fuel Tank
Capacity
66 lit. (17.4 U.S.gal., 69.7 U.S.qt., 58.0 Imp.qt.)
Fuel Filter
Type
Paper type
Fuel Pressure
Low Pressure Fuel Line
500 kPa (5.1 kgf/cm², 72.5 psi)
High Pressure Fuel Line
3.0 ~ 15.0 MPa (30.6 ~ 153.0 kgf/cm², 435.1 ~ 2175.6 psi)
Fuel Pump
Type
Electrical, in-tank type
Driven by
Electric motor
High Pressure Fuel Pump
Type
Mechanical type
Driven by
Camshaft

Sensors
Manifold Absolute Pressure Sensor (MAPS)
▷ Type: Piezo-resistive pressure sensor type
▷ Specification
Pressure
[kPa (kgf/cm², psi)]
Output Voltage (V)
20.0 (0.20, 2.9)
0.79
46.7 (0.47, 6.77)
1.84
101.3 (1.03, 14.7)
4.0

Intake Air Temperature Sensor (IATS)
▷ Type: Thermistor type
▷ Specification
Temperature
Resistance (kΩ)
C
F
-40
-40
40.93 ~ 48.35
-20
-4
13.89 ~ 16.03
0
32
5.38 ~ 6.09
10
50
3.48 ~ 3.90
20
68
2.31 ~ 2.57
40
104
1.08 ~ 1.21
60
140
0.54 ~ 0.62
80
176
0.29 ~ 0.34

Engine Coolant Temperature Sensor (ECTS)
▷ Type: Thermistor type
▷ Specification
Temperature
Resistance (kΩ)
C
F
-40
-40
48.14
-20
-4
14.13 ~ 16.83
0
32
5.79
20
68
2.31 ~ 2.59
40
104
1.15
60
140
0.59
80
176
0.32

Throttle Position Sensor (TPS) [integrated into ETC Module]
▷ Type: Variable resistor type
▷ Specification
Throttle Angle()
Output Voltage (V)
TPS1
TPS2
0
0
5.0
10
0.48
4.52
20
0.95
4.05
30
1.43
3.57
40
1.90
3.10
50
2.38
2.62
60
2.86
2.14
70
3.33
1.67
80
3.81
1.19
90
4.29
0.71
100
4.76
0.24
105
5.0
0
C.T (6~15)
0.29 ~ 0.71
4.29 ~ 4.71
W.O.T (93~102)
4.43 ~ 4.86
0.14 ~ 0.57

Item
Resistance (kΩ)
TPS1
0.875 ~ 1.625 [20C(68F)]
TPS2
0.875 ~ 1.625 [20C(68F)]

Crankshaft Position Sensor (CKPS)
▷ Type: Hall effect type
Camshaft Position Sensor (CMPS)
▷ Type: Hall effect type
Knock Sensor (KS)
▷ Type: Piezo-electricity type
▷ Specification
Item
Specification
Capacitance (pF)
850 ~ 1,150

Heated Oxygen Sensor (HO2S) [Bank 1/Sensor 1]
▷ Type: Zirconia (ZrO2) [Linear] Type
▷ Specification
Item
Specification
Heater Resistance (Ω)
2.5 ~ 4.0 [20C(69.8F)]

Heated Oxygen Sensor (HO2S) [Bank 1/Sensor 2]
▷ Type: Zirconia (ZrO2) [Binary] Type
▷ Specification
A/F Ratio (λ)
Output Voltage(V)
RICH
Approx. 0.9
LEAN
Approx. 0.04

Item
Specification
Heater Resistance (Ω)
3.3 ~ 4.1 [21C(69.8F)]

Rail Pressure Sensor (RPS)
▷ Type: Piezo-electricity type
▷ Specification

Accelerator Position Sensor (APS)
▷ Type: Variable resistor type
▷ Specification
Accelerator
Position
Output Voltage (V)
APS1
APS2
C.T
0.7 ~ 0.8
0.275 ~ 0.475
W.O.T
3.8 ~ 4.4
1.75 ~ 2.35

Fuel Tank Pressure Sensor (FTPS)
▷ Type: Piezo - Resistivity type
▷ Specification
Pressure
[kPa (kgf/cm², in H2O)
Output Voltage (V)
-3.75 (-0.038, -15.05)
4.5
0
1.5
+1.25 (0.013, 5.02)
0.5

Actuators
Injector
▷ Specification
Item
Specification
Coil Resistance (Ω)
1.18 ~ 1.31 [20C(68F)]

ETC Motor [integrated into ETC Module]
▷ Specification
Item
Specification
Coil Resistance (Ω)
1.2 ~ 1.8 [20C(68F)]

Purge Control Solenoid Valve (PCSV)
▷ Specification
Item
Specification
Coil Resistance (Ω)
19.0 ~ 22.0 [20C(68F)]

CVVT Oil Control Valve (OCV)
▷ Specification
Item
Specification
Coil Resistance (Ω)
6.9 ~ 7.9 [20C(68F)]

Variable Intake Solenoid (VIS) Valve
▷ Specification
Item
Specification
Coil Resistance (Ω)
30.0 ~ 35.0 [20C(68F)]

Fuel Pressure Control Valve
▷ Specification
Item
Specification
Coil Resistance (Ω)
0.5 [20C(68F)]

Ignition Coil
▷ Type: Stick type
▷ Specification
Item
Specification
Primary Coil Resistance (Ω)
0.62 10%[20C(68F)]
Secendary Coil Resistance (kΩ)
7.0 15%[20C(68F)]

Canister Close Valve (CCV)
▷ Specification
Item
Specification
Coil Resistance (Ω)
19.8 ~ 21.8 [20C(68F)]

Engine Control / Fuel System
...

Service Standard
Item Specification Ignition Timing () BTDC 6 10 Idle Speed (rpm) A/C OFF Neutral, N, P-range 680 100 D-range ...

See also:

Rear Glass Defogger Switch Installation
1. Install the heater control unit. 2. Install the center fascia panel. ...

Alternator Installation
1. Install in the reverse order of removal. 2. Adjust the alternator belt tension after installation. (Refer to Engine Mechanical ...

Components
2WD 1. Rear upper arm 2. Rear stabilizer bar 3. Rear lower arm 4. Rear assist arm 5. Rear shock absorber 6. Rear cross member 7. Trailing arm ...

Copyright www.ksmanual.com 2014-2019