Kia Optima Manuals

Kia Sorento: Rear Shock Absorber Removel - Rear Suspension System - Suspension System - Kia Sorento XM 2011-2026 Service ManualKia Sorento: Rear Shock Absorber Removel

Second Generation XM (2011-2026) / Kia Sorento XM 2011-2026 Service Manual / Suspension System / Rear Suspension System / Rear Shock Absorber Removel

2WD
1.
Remove the rear wheel and tire (A) from rear hub .
Tightening torque:
88.2 ~ 107.8 N.m (9.0 ~ 11.0 kgf.m, 65.0 ~ 79.5 lb-ft)
  
Be careful not to damage to the hub bolts when removing the rear wheel and tire (A).

2.
Support the rear lower arm (A) with a jack as shown in the illustration.
  
Certainly install Jack as being danger because of the tension.

3.
Loosen the bolt (A-1ea) and then remove the rear shock absorber cover (B).
Tightening torque:
5.9 ~ 9.8 N.m (0.6 ~ 1.0 kgf.m, 4.3 ~ 7.2 lb-ft)

4.
Remove the rear wheel guard.
(Refer to Body (Interior and Exterior) - "Rear Wheel Guard")
5.
Loosen the bolt (A,B) & nut (C) and then remove the rear shock absorber bracket (D).
Tightening torque:
Bolts :
(A) 137.3 ~ 159.9N.m (14.0 ~ 16.0kgf.m, 101.3 ~ 115.7lb-ft)
(B) 88.2 ~ 107.8 N.m (9.0 ~ 11.0 kgf.m, 65.0 ~ 79.5 lb-ft)
Nuts :
(C) 88.2 ~ 107.8 N.m (9.0 ~ 11.0 kgf.m, 65.0 ~ 79.5 lb-ft)

6.
Loosen the nut (A) and then remove the rear shock absorber (B).
Tightening torque:
137.3 ~ 159.9N.m (14.0 ~ 16.0kgf.m, 101.3 ~ 115.7lb-ft)

4WD
1.
Remove the rear wheel and tire (A) from rear hub .
Tightening torque:
88.2 ~ 107.8 N.m (9.0 ~ 11.0 kgf.m, 65.0 ~ 79.5 lb-ft)
  
Be careful not to damage to the hub bolts when removing the rear wheel and tire (A).

2.
Support the rear lower arm (A) with a jack as shown in the illustration.
  
Risk due to the spring tension to Honor Jack definitely fixed.

3.
Loosen the bolt (A-1ea) and then remove the rear shock absorber cover (B).
Tightening torque:
5.9 ~ 9.8 N.m (0.6 ~ 1.0 kgf.m, 4.3 ~ 7.2 lb-ft)

4.
Loosen the bolt (A) & nut (B) and then remove the rear shock absorber (C).
Tightening torque:
Bolt (A) : 137.3 ~ 159.9N.m (14.0 ~ 16.0kgf.m, 101.3 ~ 115.7lb-ft)
Nut (B) : 137.3 ~ 159.9N.m (14.0 ~ 16.0kgf.m, 101.3 ~ 115.7lb-ft)

Components
2WD 1. Rear upper arm 2. Rear stabilizer bar 3. Rear lower arm 4. Rear assist arm 5. Rear shock absorber 6. Rear cross member 7. Trailing arm ...

Rear Shock Absorber Inspection
1. Check the rubber parts for damage or deterioration. 2. Check the shock absorber for abnormal resistance or unusual sounds. ...

See also:

Replacement
The injector combustion seal should be replaced new one to prevent leakage after removing the injector. 1. Remove the combustion seal (A) with a wire cutter. ...

Antenna Removal
1. Remove the rear roof trim. (Refer to Body - "Roof trim") 2. Disconnect the power cable (A). 3. ...

Cylinder Head Reassembly
   Thoroughly clean all parts to be assembled. Before installing the parts, apply fresh engine oil to all sliding and ...

Categories

Copyright www.ksmanual.com 2014-2026