Kia Optima Manuals

Kia Sorento: Front Driveshaft Removal and Installation - Driveshaft Assembly - Driveshaft and axle - Kia Sorento XM 2011-2026 Service ManualKia Sorento: Front Driveshaft Removal and Installation

Second Generation XM (2011-2026) / Kia Sorento XM 2011-2026 Service Manual / Driveshaft and axle / Driveshaft Assembly / Front Driveshaft Removal and Installation

1.
Remove the front wheel and tire (A) from front hub .
Tightening torque:
88.2 ~ 107.8 N.m (9.0 ~ 11.0 kgf.m, 65.0 ~ 79.5 lb-ft)
  
Be careful not to damage to the hub bolts when removing the front wheel and tire (A).

2.
Remove the brake caliper mounting bolts, and then place the brake caliper assembly (B) with wire.
Tightening torque:
78.4 ~ 98.0N.m (8.0 ~ 10.0kgf.m, 57.8 ~ 72.3lb-ft)

3.
Remove the coking nut (A).
Tightening torque:
240.3~ 269.7N.m (24.5 ~ 27.5kgf.m, 177.2 ~ 198.9lb-ft)

  
•
The front hub coking nut should be replaced with new ones.
•
After installation coking nut (A), stake the coking nut using a chisel and hammer as shown in the illustration below.

4.
Remove the brake hose (A) and wheel speed sensor (B).
Tightening torque:
6.8 ~ 10.8N.m (0.7 ~ 1.1kgf.m, 5.1 ~ 7.9lb-ft)

5.
Remove the tie rod end ball joint (C) from the knuckle.
(1)
Remove the split pin (A).
(2)
Remove the castle nut (B).
Tightening torque:
34.3 ~ 44.1N.m (3.5 ~ 4.5kgf.m, 25.3 ~ 32.5lb-ft)

6.
Disconnect the ball joint(A) from knuckle using the special tool (09568-4A000).
7.
Remove the lower arm (A) mounting bolt and nut from the knuckle.
Tightening torque:
98.0 ~ 117.6N.m (10.0 ~ 12.0kgf.m, 72.3 ~ 86.7lb-ft)

8.
Using a plastic hammer (A), disconnect driveshaft (C) from the axle hub (B).

9.
Remove the RH side cover (A).
Tightening torque:
7.8 ~ 11.8N.m (0.8 ~ 1.2kgf.m, 5.8 ~ 8.7lb-ft)

10.
Remove the mounting bolts (A,B) of Upper roll rod bracket (C).
Tightening torque:
(A) 107.9 ~ 125.5N.m (11.0 ~ 13.0kgf.m, 79.6 ~ 94.0lb-ft)
(B) 49.0 ~ 63.7N.m (5.0 ~ 6.5kgf.m, 36.2 ~ 47.0lb-ft)
  
Do not reuse bolts.

11.
Loosen the inner shaft mounting bolts and then disconnect the inner shaft (A).
Tightening torque:
49.0 ~ 68.6N.m (5.0 ~ 7.0kgf.m, 36.2 ~ 50.6lb-ft)
  
By the shape and the engine bracket bolts are mounted differently.

12.
Insert a pry bar (A) between the transaxle case and joint case, and separate the drive shaft (B) from the transaxle case.
13.
Install in the reverse order of removal.
  
•
Use a pry bar being careful not to damage the transaxle and joint.
•
Do not insert the pry bar too deep, as this may cause damage to the oil seal.
•
Do not pull the driveshaft by excessive force it may cause components inside the joint kit to dislodge resulting in a torn boot or a damaged bearing.
•
Plug the hole of the transaxle case with the oil seal cap to prevent contamination.
•
Support the driveshaft properly.
•
Replace the retainer ring whenever the driveshaft is removed from the transaxle case.
Front Driveshaft Components
1. Front driveshaft (LH) 2. Inner shaft bearing bracket 3. Front driveshaft (RH) [LH] 1. BJ assembly 2. Clip 3. BJ boot band 4. BJ bo ...

TJ Joint Components
[LH] 1. BJ assembly 2. BJ circlip 3. BJ boot band 4. BJ boot 5. Shaft 6. TJ boot band 7. TJ boot 8. Spider assembly 9. Retainer ring 10. ...

See also:

Auto Light Sensor Inspection
In the state of IGN1 ON, when multi function switch module detects auto light switch on, tail lamp relay output and head lamp low relay output are controlled according to auto light sensor ...

Tilt and telescopic steering
Tilt and telescopic steering allows you to adjust the steering wheel before you drive.You can also raise it to give your legs more room when you exit and enter the vehicle. The steering wheel shoul ...

Power outlet
The power outlet is designed to provide power for mobile telephones or other devices designed to operate with vehicle electrical systems. The devices should draw less than 10 amps with the engine ...

Categories

Copyright www.ksmanual.com 2014-2026