Kia Sorento: Specification
Ignition Coil
Item
|
Specification
|
Primary Coil Resistance (Ω)
|
0.62 ± 10％ [20°C (68°F)]
|
Secondary Coil Resistance (kΩ)
|
7.0 ± 15％ [20°C (68°F)]
|
Spark plug
Item
|
Specification
|
Type
|
FXU16HR11
|
Gap
|
1.0 ~1.1 mm
(0.0394 ~ 0.0433 in.)
|
Condenser
Item
|
Specification
|
Capacitance (uF)
|
0.47 [1KHz]
|
Insulation resistance (MΩ)
|
1,000 [DC 500 V/1 Min]
|
Alternator
Item
|
Specification
|
Rated voltage
|
13.5V, 130A
|
Speed in use
|
1,000 ~ 18,000 rpm
|
Voltage regulator
|
IC Regulator built-in type
|
Regulator Setting Voltage
|
External mode
|
Refer to below graph
|
Internal mode
|
14.55 ± 0.3V
|
Temperature Gradient
|
External mode
|
0 ± 3 mV / °C
|
Internal mode
|
-3.5 ± 2mV / °C
|
※ Regulator Setting Voltage (External mode)
Battery
Item
|
Specification
|
Model type
|
CMF68L-BCI
|
Capacity [20HR/5HR] (AH)
|
68 / 54
|
Cold Cranking Amperage (A)
|
600 (SAE) / 480 (EN)
|
Reserve Capacity (Min)
|
110
|
| •
|
Model type description
|
| •
|
Cold Cranking Ampere (CCA): Cold Cranking Amps is a rating
used in the battery industry to define a battery's ability to
start an engine in cold temperatures.
|
| -
|
The rating is the number of amps a new, fully charged
battery can deliver at -18 °C(-0.4 °F) for 30 seconds, while
maintaining a voltage of at least 7.2 volts for a 12 volt battery.
|
| -
|
The higher the CCA rating, the greater the starting power
of the battery.
|
| •
|
RESERVE CAPACITY (RC) : Reserve Capacity is a battery
industry rating, defining a battery's ability to power a vehicle
with an inoperative alternator or fan belt.
|
| -
|
The rating is the number of minutes a battery at 26.7
°C(80 °F) can be discharged at 25 amps and maintain a voltage
of 10.5 volts for a 12 volt battery.
|
| -
|
The higher the reserve rating, the longer your vehicle
can operate should your alternator or fan belt fail.
|
|
Starter
Item
|
Specification
|
Rated voltage
|
12 V, 1.2 kW
|
The number of pinion teeth
|
11
|
Performance
[No-load, 11 V]
|
Ampere
|
Max. 70 A
|
Speed
|
Min. 2,400 rpm
|
Item
N.m
kgf.m
lb-ft
Ignition coil installation bolt
9.8 ~ 11.8
1.0 ~ 1.2
7.2 ~ 8.7
Spark plug installation
14.7 ~ 24. ...
See also:
Instrument Cluster Installation
1.
Connect the cluster connector.
2.
Install the cluster assembly.
3.
Install the cluster facia panel.
...
Seat Belt Buckle Switch (BS) Description
The SRSCM shall monitor the status of the driver and front passenger seat
belt buckle. The SRSCM provides one pin each for the driver and front passenger
seat belt buckle status input. The se ...
Rear Driveshaft Inspection
1.
Check the driveshaft boots for damage and deterioration.
2.
Check the ball joint for wear and damage.
3.
Che ...
Tightening Torques