Kia Sorento: Engine Oil: Oil and filter replacement - Lubrication System - Engine Mechanical System - Kia Sorento XM 2011-2024 Service ManualKia Sorento: Engine Oil: Oil and filter replacement

Second Generation XM (2011-2024) / Kia Sorento XM 2011-2024 Service Manual / Engine Mechanical System / Lubrication System / Engine Oil: Oil and filter replacement

  
•
Prolonged and repeated contact with mineral oil will result in the removal of natural fats from the skin, leading to dryness, irritation and dermatitis. In addition, used engine oil contains potentially harmful contaminants which may cause skin cancer.
•
Exercise caution in order to minimize the length and frequency of contact of your skin to used oil. Wear protective clothing and gloves. Wash your skin thoroughly with soap and water, or use water-less hand cleaner, to remove any used engine oil. Do not use gasoline, thinners, or solvents.
•
In order to preserve the environment, used oil and used oil filter must be disposed of only at designated disposal sites.
1.
Park the car on level ground.
Start the engine and let it warm up.
2.
Drain engine oil.
(1)
Remove the oil filler cap.
(2)
After lifting the car, remove the oil drain plug hole cover.
(3)
Remove the oil drain plug and drain oil into a container.
3.
Remove the oil filter with the SST(09263-2E000, the oil filter wrench).
(1)
Remove the oil filter.
(2)
Check and clean the oil filter installation surface.
(3)
Check the part number of the new oil filter is as same as old one.
(4)
Apply clean engine oil to the gasket of a new oil filter.
(5)
Lightly screw the oil filter into place, and tighten it until the gasket contacts the seat.
(6)
Tighten it with the torque below.

Tightening torque :
11.8 ~ 15.7 N.m (1.2 ~ 1.6 kgf.m, 8.7 ~ 11.6 lb-ft)

4.
Install the oil drain plug with a new gasket.

Tightening torque :
34.3 ~ 44.1 N.m (3.5 ~ 4.5 kgf.m, 25.3 ~ 32.5 lb-ft)

5.
Fill with new engine oil, after removing the engine oil level gauge.

Capacity
Total : 5.8L (1.53U.S.gal., 6.13U.S.qt., 5.10lmp.qt.)
Oil pan : 4.4L (1.16U.S.gal., 4.65U.S.qt., 3.87lmp.qt.)
Drain and refill including oil filter : 4.8L (1.27U.S.gal., 5.07U.S.qt., 4.22lmp.qt.)

6.
Install the oil filler cap.
7.
Start engine and check for oil leaks and check the oil gauge or light for an indication of oil pressure.
8.
Recheck the engine oil level.
Lubrication System
...

Engine Oil Inspection
1. Check the engine oil quality. Check the oil deterioration, entry of water, discoloring of thinning. If the quality is visibly poor, replace the oil. ...

See also:

Description
Crankshaft Position Sensor (CKPS) detects the crankshaft position and is one of the most important sensors of the engine control system. If there is no CKPS signal input, the engine may stop ...

Auto Head lamp leveling Unit Description
According to driving environment and loading state of vehicle, head lamp lighting direction is changed to keep the driver's visibility range and to protect the driver's vision from gl ...

Component Location
[Engine Room] 1. Receiver-drier 2. Condenser 3. Ambient temperature Sensor 4. Compressor 5. Discharge Hose 6. Suction & Liquid Tube Assembly 7. Servic ...

Copyright © www.ksmanual.com 2014-2024