Kia Sorento: Rear Seat Replacement - Seat & Power Seat - Body (Interior and Exterior) - Kia Sorento XM 2011-2024 Service ManualKia Sorento: Rear Seat Replacement

Second Generation XM (2011-2024) / Kia Sorento XM 2011-2024 Service Manual / Body (Interior and Exterior) / Seat & Power Seat / Rear Seat Replacement

Rear Seat Assembly Replacement
[Second row seat assembly]
1.
Push the second row seat assembly [RH] (A) towards the front of the vehicle as far as possible.

2.
Loosen the second center seat belt buckle mounting bolt (A).

Tightening torque :
39.2 ~ 53.9 N.m (4.0 ~ 5.5 kgf.m, 28.9 ~ 39.8 lb-ft)

3.
Push the second row seat assembly towards the front of the vehicle as far as possible.
4.
Loosen the second row seat assembly rear mounting bolts (A).

Tightening torque :
16.7 ~ 25.5N.m (1.7 ~ 2.6kgf.m, 12.3~18.8lb-ft)

[LH]

[RH]

5.
Push the second row seat assembly towards the rear of the vehicle as far as possible.
6.
After loosening the mounting bolts, then remove the second row seat assembly (A).

Tightening torque :
16.7 ~ 25.5N.m (1.7 ~ 2.6kgf.m, 12.3~18.8lb-ft)

7.
Install in the reverse order of removal.
[Third row seat assembly]
1.
Remove the luggage box trim (A).

2.
Remove the luggage box partition trim (A).

3.
Loosen the third row seat assembly rear mounting bolts (A).

Tightening torque :
16.7 ~ 25.5N.m (1.7 ~ 2.6kgf.m, 12.3~18.8lb-ft)

4.
Remove the third row seat track mounting cover (A).

5.
After loosening the mounting bolts, then remove the third row seat assembly (A).

Tightening torque :
16.7 ~ 25.5N.m (1.7 ~ 2.6kgf.m, 12.3~18.8lb-ft)

6.
Install in the reverse order of removal.
Rear Seat Back Cover Replacement
[Second row seat assembly]
(LH)
  
•
Put on gloves to protect your hands.
  
•
Pry the trim off using a plastic trim tool and apply protective tape around the related parts, to prevent damage.
•
Use a plastic panel removal tool to remove interior trim pieces to protect from marring the surface.
•
Take care not to bend or scratch the trim and panels.
1.
Remove the second row seat assembly [LH].
(Refer to Rear Seat - "Rear Seat Assembly")
2.
Tilt the rear back armrest towards the front of the vehicle as far as possible.
3.
To remove the rear back armrest (B), loosen the mounting bolts after removing the caps (A).

4.
Remove the rear back armrest pad (B) by pulling it out while pressing the both sides of the lock pin (A).

5.
After loosening the mounting bolt and nuts, then remove the rear back armrest bracket (A).

6.
After loosening the mounting bolt, then remove the rear back armrest panel (A).

7.
Push the lock pin (B), remove the rear seat headrest (A).

8.
Using a screwdriver or remover, remove the rear center seat belt upper anchor cover (A).

9.
Remove the rear seat latch mounting support (A) after turning it counter clockwise.

10.
Using a screwdriver or remover, remove the rear seat folding cover (A).

11.
After loosening the mounting screw, then remove the rear seat shield outer cover (A).

12.
Remove the protector (A) located in the bottom side of the rear seat cushion.

13.
Remove the protector (A) located in the bottom side of the rear seat back.

14.
Remove the protector (A) located in the side part of the rear seat back.

15.
Remove the protector (A) located in the upper side of the rear seat back.

16.
Turn the rear seat back cover inside out. Then pull out the headrest guides (A) while pinching the upper part of the guides, and remove them.

17.
Remove the rear seat back cover (A) from the rear seat back frame.

18.
After removing the velcro tape (A) on the rear of seat back and remove the rear seat back cover (B).

19.
Install in the reverse order of removal.
  
•
Replace any damaged clips.
(RH)
  
•
Put on gloves to protect your hands.
  
•
Pry the trim off using a plastic trim tool and apply protective tape around the related parts, to prevent damage.
•
Use a plastic panel removal tool to remove interior trim pieces to protect from marring the surface.
•
Take care not to bend or scratch the trim and panels.
1.
Remove the second row seat assembly [RH].
(Refer to Rear Seat - "Rear Seat Assembly")
2.
Push the lock pin (B), remove the rear seat headrest (A).

3.
Using a screwdriver or remover, remove the rear seat folding cover (A).

4.
After loosening the mounting screw, then remove the rear seat shield outer cover (A).

5.
After loosening the mounting screw, then remove the rear seat shield inner cover (A).

6.
Remove the protector (A) located in the bottom side of the rear seat cushion.

7.
Remove the protector (A) located in the bottom side of the rear seat back.

8.
Remove the protector (A) located in the side part of the rear seat back.

9.
Remove the protector (A) located in the side of the inner part of the rear seat back.

10.
Remove the protector (A) located in the upper side of the rear seat back.

11.
Turn the rear seat back cover inside out. Then pull out the headrest guides (A) while pinching the upper part of the guides, and remove them.

12.
Remove the rear seat back cover (A) from the rear seat back frame.

13.
After removing the velcro tape (A) on the rear of seat back and remove the rear seat back cover (B).

14.
Install in the reverse order of removal.
  
•
Replace any damaged clips.
[Third row seat assembly]
  
•
Put on gloves to protect your hands.
  
•
Pry the trim off using a plastic trim tool and apply protective tape around the related parts, to prevent damage.
•
Use a plastic panel removal tool to remove interior trim pieces to protect from marring the surface.
•
Take care not to bend or scratch the trim and panels.
1.
Remove the third row seat assembly.
(Refer to Rear Seat - "Rear Seat Assembly")
2.
Push the lock pin (B), remove the rear seat headrest (A).

3.
Loosen the rear seat frame mounting bolts (A).

Tightening torque :
44.1 ~ 53.9 N.m (4.5 ~ 5.5 kgf.m, 32.5 ~ 39.8 lb-ft)

4.
Push the rear seat cushion frame (A) to the front of the vehicle as far as possible.

5.
Remove the protector (A) located in the side part of the rear seat back.

6.
Remove the protector (A) located in the bottom side of the rear seat back.

7.
Turn the rear seat back cover inside out. Then pull out the headrest guides (A) while pinching the upper part of the guides, and remove them.

8.
Remove the rear seat back cover (A) from the rear seat back frame.

9.
After removing the velcro tape (A) on the rear of seat back and remove the rear seat back cover (B).

10.
Install in the reverse order of removal.
  
•
Replace any damaged clips.
Rear Seat Cushion Cover Replacement
[Second row seat assembly]
(LH)
  
•
Put on gloves to protect your hands.
  
•
Pry the trim off using a plastic trim tool and apply protective tape around the related parts, to prevent damage.
•
Use a plastic panel removal tool to remove interior trim pieces to protect from marring the surface.
•
Take care not to bend or scratch the trim and panels.
1.
Remove the second row seat assembly [LH].
(Refer to Rear Seat - "Rear Seat Assembly")
2.
Remove the protector (A) located in the bottom side of the rear seat cushion.

3.
After loosening the mounting screw, then remove the rear seat slide knob (A).

4.
After loosening the mounting screw, then remove the rear seat slide outer cover (A).

5.
Remove the protector (A) located in the side part of the rear seat cushion.

6.
Remove the rear seat cushion cover (A) from the rear seat cushion frame.

7.
After removing the velcro tape (A) on the rear of seat cushion and remove the rear seat cushion cover (B).

8.
Install in the reverse order of removal.
  
•
Replace any damaged clips.
(RH)
  
•
Put on gloves to protect your hands.
  
•
Pry the trim off using a plastic trim tool and apply protective tape around the related parts, to prevent damage.
•
Use a plastic panel removal tool to remove interior trim pieces to protect from marring the surface.
•
Take care not to bend or scratch the trim and panels.
1.
Remove the second row seat assembly [RH].
(Refer to Rear Seat - "Rear Seat Assembly")
2.
Remove the protector (A) located in the bottom side of the rear seat cushion.

3.
After loosening the mounting screw, then remove the rear seat slide knob (A).

4.
After loosening the mounting screw, then remove the rear seat slide outer cover (A).

5.
Remove the protector (A) located in the side part of the rear seat cushion.

6.
Remove the rear seat cushion cover (A) from the rear seat cushion frame.

7.
After removing the velcro tape (A) on the rear of seat cushion and remove the rear seat cushion cover (B).

8.
Install in the reverse order of removal.
  
•
Replace any damaged clips.
[Third row seat assembly]
  
•
Put on gloves to protect your hands.
  
•
Pry the trim off using a plastic trim tool and apply protective tape around the related parts, to prevent damage.
•
Use a plastic panel removal tool to remove interior trim pieces to protect from marring the surface.
•
Take care not to bend or scratch the trim and panels.
1.
Remove the third row seat assembly.
(Refer to Rear Seat - "Rear Seat Assembly")
2.
Loosen the rear seat frame mounting bolts (A).

Tightening torque :
44.1 ~ 53.9 N.m (4.5 ~ 5.5 kgf.m, 32.5 ~ 39.8 lb-ft)

3.
Push the rear seat cushion frame (A) to the front of the vehicle as far as possible.

4.
After loosening the mounting screw, then remove the rear seat outer link cover (A).

5.
After loosening the mounting screw, then remove the rear seat inner link cover (A).

6.
Remove the protector (A) located in the side part of the rear seat cushion.

7.
Remove the rear seat cushion cover (A) from the rear seat cushion frame.

8.
After removing the velcro tape (A) on the rear of seat cushion and remove the rear seat cushion cover (B).

9.
Install in the reverse order of removal.
  
•
Replace any damaged clips.
Rear Seat Latch Replacement
[Second row seat assembly]
  
•
Put on gloves to protect your hands.
Front Seat Replaccement
Seat Assembly Replacement 1. Remove the seat assembly mounting cover. 2. After loosening the seat assembly mounting bolts, remove the seat ...

Seat Belt
...

See also:

Special Service Tools
Tools (Number and name) Illustration Use 09200-3N000 Engine support fixture(Beam) Removal and installation of the transaxle. Except lo ...

Front Door Components
1. Door grip handle cover 2. Door inside handle cap 3. Door trim 4. Door belt inner weatherstrip 5. Door module 6. Quadrant inner cover 7. Door belt weatherstrip 8. ...

Power Door Lock Switch Diagnosis With GDS
1. It will be able to diagnose defects of door lock with GDS quickly. GDS can operates actuator forcefully, input/output value monitoring and self diagnosis. ...

Copyright © www.ksmanual.com 2014-2024